E. Sjödin
Institute of Applied Hydraulics, Örnsköldsvik, Sweden
Per-Oskar Westin
Institute of Applied Hydraulics, Örnsköldsvik, Sweden
Ladda ner artikel
http://dx.doi.org/10.3384/ecp1392a40Ingår i: 13th Scandinavian International Conference on Fluid Power; June 3-5; 2013; Linköping; Sweden
Linköping Electronic Conference Proceedings 92:40, s. 409-415
Publicerad: 2013-09-09
ISBN: 978-91-7519-572-8
ISSN: 1650-3686 (tryckt), 1650-3740 (online)
In this study two systems for detection of pitting damage in low speed hydraulic motors were compared. These systems were based on an optical particle detector and a magnetic plug respectively. The purpose of the comparison was to determine the relative effectiveness of two methods for detecting pitting damage in a low speed hydraulic motor. In order to do this extensive testing was conducted in Bosch Rexroth Mellansel AB laboratory in Mellansel; Sweden. In the course of the project two post-processing algorithms were developed to enable automatic triggering of alarms based on measurement values from the optical sensor. The optical sensor showed earlier indication of damage than the magnetic plug and the algorithms produced automatic alarms; but there was also a higher false alarm rate when using the optical sensor compared to the magnetic plug
[1] J. Halme and P. Andersson; "Rolling contact fatigue and wear fundamentals for rolling bearing diagnostics - state of the art;" Proceedings of the Institution of Mechanical Engineers; Part J: Journal of Engineering Tribology; no. 224; pp. 377-393; 2010.
[2] D. Nilsson; "Investigations for Enhanced Tribological Performance of a Hydraulic Motor;" Doctoral Thesis; Luleå University of Technology; 2011.
[3] R. Ahmad and S. Kamaruddin; "An overview of time-based and condition-based maintenance in industrial application.;" Computers & Industrial Engineering; vol. 63; no. 1; pp. 135-149; 2012.
[4] D. Nilsson and S. Berg; "Wear and life of roller bearings under low speed and clean environment; a comparison of Me-C:H coated and uncoated rollers;" in Nordic Symposium on Tribology; 2002.
[5] J. A. Briggs; "Determining contamination levels in hydraulic systems;" in Annual Meeting; American Society of Lubrication Engineers; 1969.
[6] F. D. Norvelle; "Contamination control — the key to reliability in fluid power systems;" Wear; vol. 94; no. 1; pp. 47-70; 1984.
[7] L. Arvidsson; "Partikelräkning eller gravimetri vid föroreningsanalys av hydraulolja;" Fluid Scandinavia; no. 3; 1997.
[8] C. Evans; "Wear debris analysis and condition monitoring;" NDT international; no. June; pp. 132-134; 1978.
[9] R. Sjölund and E. Söderkvist; "Tillståndskontroll av hydraulmotorer med hjälp av magnetindikator;" Master’s Thesis; Luleå University of Technology; Luleå; 2006.
[10] S. Dory and T. Hansen; "Magnetic plug inspection enhanses condition-based maintenance;" Practicing Oil Analysis; no. September; 2003.
[11] M. H. Jones; "Particle Transfer from Magnetic Plugs;" Swansea Tribology Services Ltd.; University of Wales Swansea; 1998.
[12] S. Raaduni; "Magnetic Chip Detector (MCD) Wear Particle Analysis;" King Mongkut’s University of Technology; Bangkok; 2002.
[13] P. J. Dempsey; "Gear Damage Detection Using Oil Debris Analysis;" NASA; Glenn Research Center; Cleveland; Ohio; 2001.
[14] P. J. Dempsey and A. A. Afjeh; "Integrating Oil Debris and Vibration Gear Damage Detection Technologies Using Fuzzy Logic;" in International 58th Annual Forum and Technology Display; Montreal; 2002.
[15] P. J. Dempsey; G. Kreider and T. Fichter; "Investigation of Tapered Roller Bearing Damage Detection Using Oil Debris Analysis;" Power transmission engineering; february 2007.
[16] D. G. Lewicki; P. J. Dempsey; G. J. Heath and P. Shanthakumaran; "Gear Fault Detection Effectiveness as Applied to Tooth Surface Pitting Fatigue Damage;" National Aeronautics and Space Administration; Washington; DC; 2009.
[17] J. L. Miller and D. Kitaljevich; "In-line oil debris monitor for aircraft engine condition assessment;" in IEEE Aerospace conference proceedings; 2000.
[18] M. Craig; T. J. Harvey; R. J. K. Wood; K. Masuda; M. Kawabata and H. E. G. Powrie; "Advanced condition monitoring of tapered roller bearings; Part 1;" Tribology International; vol. 42; no. 11-12; pp. 1846-1856; 2009.
[19] S. Sjöberg; "Partikelräkning eller gravimetri för föroreningsbestämning av hydraulolja;" Fluid Scandinavia; no. 1; 1997.
[20] B. Andersson; "Jämförande utvärdering av partikelräknare;" Fluid Scandinavia; no. 5; 1996.
[21] A. Östgren; "Mätning av föroreningar i hydraulolja med automatisk partikelräknare;" LTU; Luleå; 1996.
[22] B. Verdegan; A. True-Dahl; W. Haberkamp; N. Blizard; D. Genter and E. Quillen; "Filtration Solutions for High Pressure Common Rail Fuel Systems;" Cummins Inc.; 2008.
