Jyrki Parkkinen
Aalto University, School of Electrical Engineering, Department of Automation and Systems Technology, Helsinki,Finland
Kai Zenger
Aalto University, School of Electrical Engineering, Department of Automation and Systems Technology, Helsinki,Finland
Joonas Ollila
Aalto University, School of Electrical Engineering, Department of Automation and Systems Technology, Helsinki,Finland
Ladda ner artikel
http://dx.doi.org/10.3384/ecp1392a46Ingår i: 13th Scandinavian International Conference on Fluid Power; June 3-5; 2013; Linköping; Sweden
Linköping Electronic Conference Proceedings 92:46, s. 465-474
Publicerad: 2013-09-09
ISBN: 978-91-7519-572-8
ISSN: 1650-3686 (tryckt), 1650-3740 (online)
In this paper; some statistical methods to the energy efficiency issue in industrial pneumatic systems are presented. Since all compressed air (CA) systems are different; in industrial applications it may be difficult to analyse energy efficiency of a single CA system from a theoretical model-based viewpoint. Instead of modeling the industrial pneumatic system from first principles the energy efficiency of the system is analyzed based on time series measurements. The dependency between energy consumption; potential variable pressure and flow variable mass flow makes possible to draw conclusions of the energy efficiency based on the measurements of pressure and power/energy.
In woodworking industry; e.g. sawmills; the functioning of the assembly line is relatively monotonic from day to day. Typically; CA is almost entirely used for linear motions. A double acting cylinder is the most common actuator in these applications. The length of the impact; the radius of the piston and radius of the cylinder are the essential key figures of this cylinder type. From these figures and basic dynamics of the cylinder; the air volume per impact can be obtained. When the average values and standard deviation of the air flow in each consumption point (cylinder) is known; statistical methods can be implemented for the total consumption of CA. According to the Central Limit Theorem; the total air consumption; i.e the sum of consumptions in different consumption points; can be assumed to be normal-distributed. Since the consumed air flow is proportional to the compressor’s energy consumption; the trend of energy can also be approximated as a sum of regression curve and normally distributed deviation component. By this result; a confidence interval for energy consumption can be determined. The result is also ready to be used in energy saving calculations in the future.
Also; the adjustable pressure-difference in a two-point controlled compressor has an essential effect on the overall energy efficiency of the system. When this pressure difference is large; the system is not optimal from the viewpoint of energy efficiency. Typically the time series measurements of pressure are somewhat noisy; but some kind of conclusions of stationary behavior can be done. After possible pre-filtering process of the data; it becomes evident that the measurement data signal is typically a periodic shape with strict minimum and maximum values. The consumption of CA is typically dependent on pressure i.e. higher pressure increases consumption making the shape of pressure curve exponential. A stationary time series described by its mean; variance and autocorrelation function makes possible to identify the essential features of the dynamics of the CA system and the type of consumption.
With the appropriate statistical methods; the results of short-time measurements can be applied for predicting the energy consumption trend in a long run. The combination of first principle modeling with measurements opens new methods in energy efficiency techniques especially when designing new pneumatic systems or the improving of existing designs
Pneumatics in woodworking industry; time series analysis; estimate; confidence interval; autocorrelation
[1] P Radgen; E Blaustein. (Eds) Compressed Air Systems in the European Union: Energy; Emission; Savings Potential and Policy Actions 2001
[2] The Energy Research Institute; Department of Mechanical Engineering ; University of Cape Town How to save energy and money: Guide Book 3: Compressed Air Systems 2007
[3] Paul H Harris; Garret O’Donnell; Tim Whelan Energy Efficiency in Pneumatic Production Systems: State of the Art and Future Directions Leveraging Technology in a Sustainable World Proceedings of the 19th CIRP Conference on Life Cycle Engineering; University of California at Berkeley; Berkeley; USA 2012
[4] Paul H Harris; Garret O’Donnell; Tim Whelan. Predictive Consumption Models for Electro-Pneumatic Production Systems. IEEE Transactions on Mechatronics 2011
[5] Susanne V Krichel; O Savodny. Analysis and optimization of compressed air networks with model-based approaches; Ventil 17/2011
[6] Susanne V Krichel; O Savodny. Dynamic modeling of pneumatic transmission lines in MATLAB/SIMULINK Proceedings of the International Fluid Power and Mechatronics Conference; Beijing/China 2011
[7] J Parkkinen. Energy Efficiency in Industrial Pneumatic Systems Helsinki University of Technology Control Engineering Laboratory Espoo 2007 (lic.thesis)
[8] J Parkkinen; K Zenger. A new Efficiency Index for Analysing and Minimising Energy Consumption in Pneumatic Systems Int. Journal of Fluid Power2008
[9] G.E.P Box; G.M. Jenkins ; G.C. Reinsel : Time Series Analysis: Forecasting and Control John Wiley & Sons;Inc 2008
[10] J Parkkinen. Improving Energy Efficiency in Industrial Pneumatic Systems by Structural Means The Twelfth Scandinavian International Conference on Fluid Power 2011; Tampere; Finland
[11] V.Hölttä: Analysis of stem diameter measurement in forest harvester (diploma thesis)2004
