S. W. Chiang
Graduate Institute of Environmental Engineering, Nation Taiwan University, Taiwan
C. C. Chang
Graduate Institute of Environmental Engineering, Nation Taiwan University, Taiwan
H. Y. Chang
Graduate Institute of Environmental Engineering, Nation Taiwan University, Taiwan
C. Y. Chang
Graduate Institute of Environmental Engineering, Nation Taiwan University, Taiwan
Ladda ner artikel
http://dx.doi.org/10.3384/ecp11057537Ingår i: World Renewable Energy Congress - Sweden; 8-13 May; 2011; Linköping; Sweden
Linköping Electronic Conference Proceedings 57:72, s. 537-545
Publicerad: 2011-11-03
ISBN: 978-91-7393-070-3
ISSN: 1650-3686 (tryckt), 1650-3740 (online)
This study examined the transformation of the biomass gasification synthesis gas (syngas; CO and H
2) to liquid fuels and chemicals via the high pressure fixed packed bed (HPFPB). The MoS
2/?-Al
2O
3 catalyst was packed in the packed bed (PB) to enhance the selectivity (S) and yield (Y) products. The effect of reaction temperature (T); pressure (P
ST ); gas flow rate (Q
G) and H
2/CO (vol./vol.) ratio oon the system performance were investigated. Typical reaction conditions unless otherwise specified were as follows: T = 423; 473; 523 and 573 K; P
ST = 3 Mpa; Q
G = 300 cm
3 min
-1; and mass of catalyst (m
S) = 30 g.
The main products include CH4; C2H6 and C2H5OH (EtOH) that EtOH being the target product. The results indicate that with packing MoS2/?-Al2O3 catalyst in PB; the conversion of CO (XCO) and alcohol production rate (R) are highly depended on T. At T = 573 K; XCO = 8.19%; R of CH4 (RCH4) = 194.1 mg h-1 and selectivity of CH4 (SCH4) = 34.57%. For the production rate of C2H5OH (REtOH); the maximum REtOH of 134.25 mg h-1 takes place at T = 523 K while XCO = 8.10% and SEtOH = 51.98%. As T increase to 573 K; the EtOH is further decomposed into simple hydrocarbons (HCs) such as C1-C3 alkanes. Thus; for producing more alcohols and less alkanes; the optimal temperature condition is 523 K. For the case of varying H2/CO ratio; the values of XCO are about 7.55 to 8.32%) at 523 K with H2/CO ratios of 1 to 4; indicating no significant variation. However; the optimal ratio of H2 and CO to produce EtOH is 2 with maximum REtOH = 134.25 mg h-1 and SEtOH = 51.98% while XCO = 8.10%; RCH4 = 56.05 mg h-1 and SCH4 = 10.85%. Hence; increasing the H2/CO ratio to 3 to 4 is not beneficial for the formation of EtOH. The results also show that a higher PST of HPFPB yields more products. For the EtOH production; the maximum REtOH (= 156.65 mg h-1) occurs at PST = 3.6 Mpa with corresponding SEtOH = 51.16%; XCO = 9.57%; RCH4 = 70.31 mg h-1 and SCH4 = 12.46%. Among various QG of 300; 450; 600 to 900 mL min-1 of HPFPB tested; the best XCO is at QG = 300 mL min-1 with XCO = 8.10%; RCH4 = 56.05 mg h-1 and SCH4 = 10.85%. Also; the maximum YEtOH take place at QG = 300 mL min-1 with corresponding SEtOH = 51.98%. It shows that a low flow rate gives a longer residence time for reaction of the syngas and thus enhances the yield of products. However; there’s no advance for SEtOH.
For the production of EtOH from syngas; the YEtOH; SEtOH and REtOH are key factors for the success of process. The results of this study shows that MoS2/γ-Al2O3 catalyst can give satisfactory SEtOH and REtOH; especially the YEtOH high selectivity.
Reforming of syngas; Synthesis of alcohol; MoS2/Al2O.; catalytic synthesis; alcohol; alkane
[1] Spivey; J.J. and A. Egbebi; Heterogeneous catalytic synthesis of ethanol from biomass-derived syngas. Chemical Society Reviews; 2007. 36(9): p. 1514-1528.
doi: 10.1039/b414039g.
[2] Ragauskas; A.J.; et al.; The path forward for biofuels and biomaterials. Science; 2006. 311(5760): p. 484-489.
doi: 10.1126/science.1114736.
[3] Subramani; V. and S.K. Gangwal; A review of recent literature to search for an efficient catalytic process for the conversion of syngas to ethanol. Energy & Fuels; 2008. 22(2): p. 814-839.
doi: 10.1021/ef700411x.
[4] Haider; M.A.; M.R. Gogate; and R.J. Davis; Fe-promotion of supported Rh catalysts for direct conversion of syngas to ethanol. Journal of Catalysis; 2009. 261(1): p. 9-16.
doi: 10.1016/j.jcat.2008.10.013.
[5] Li; D.; et al.; The performances of higher alcohol synthesis over nickel modified K2CO3/MoS2 catalyst. Fuel Processing Technology; 2007. 88(2): p. 125-127.
doi: 10.1016/j.fuproc.2004.10.008.
[6] Li; D.B.; et al.; Higher alcohol synthesis over a La promoted Ni/K2CO3/MoS2 catalyst. Catalysis Communications; 2004. 5(10): p. 605-609.
doi: 10.1016/j.catcom.2004.07.011.
[7] Woo; H.C.; et al.; Alkali-promoted MoS2 catalysts for alcohol synthesis- the effect of alkali promotion and preparation condition on activity and selectivity. New Frontiers in Catalysis; Pt C; 1993. 75: p. 2749-2752.
doi: 10.1016/S0167-2991(08)64396-7.
[8] Sakashita; Y.; Y. Araki; and H. Shimada; Effects of surface orientation of alumina supports on the catalytic functionality of molybdenum sulfide catalysts. Applied Catalysis a-General; 2001. 215(1-2): p. 101-110.
[9] Egbebi; A. and J.J. Spivey; Effect of H2/CO ratio and temperature on methane selectivity in the synthesis of ethanol on Rh-based catalysts. Catalysis Communications; 2008. 9(14): p. 2308-2311.
doi: 10.1016/j.catcom.2008.05.011.